outer bezel - Installing iPad 2 Wi-Fi replace a broken LCD Manual Guide

Posted in Apple on 24th July 2012

The installation of Wi-Fi iPad 2 replace a defective LCD Manual Guide
The tools used in this manual Here if you want to see directly this pdf manual guide whit the figures
Heat gun or hair dryer (1)
Screwdriver Phillips # 00 (1)
Opening plastic tools (1)
IFixit option of playing the guitar 8 (1)
Use this guide to replace a defective LCD.

Step 1 – Front Panel
The iPad 2 is open a very difficultdevice. Before you try this guide to know that you can have your front panel and / or plastic deform, break open sequence.In bezelaround the following steps, you will use a heat gun for adhesive to secure the smoothing panel in thefront back. Try not to melt contact toallow the hot air stream thin plastic travel around the outer edge of the front panel LRIS and become permanently deformed, and the loss of heat in the front panel, in order to solve Isto texture . When the adhesive on the areashighlighted in red in the second image. When lever on the front, especially the carefulnot INBLUE the wireless antenna in the box area or scanner cable is damage to the area outlined blackin image. second uses a heat gun to heat gently, theright front panel button. Home does not heat the home button as / a little background isplastic and deformed.
Step 2
Once the front panel area to the right of the button thehome heated sufficiently, shouldbe easy to insert an instrument for opening plastic between the plastic cover and the right side theouter beside the button inthe house. Use its plastic opening tool to create a soft smallgap inthe between the faceplate and the outer bezel to the right of the house button.If the adhesive is difficult to separate, fear don’tbe heat again. Excessivelyprying and fold the front panel of the theadhesive not flexible enough, you can easily make the tocrack. Place a selection list in the small room, the opening created by the theplastic tool.
Step 3
Heat the area on the front panel to the right of the button at the bottom yourway thehome and closer to the lower right corner of the iPad. Slide the first guitar to get the iPhone right corner and make a guitar pick tomaintain other the difference between the front and theiPad beside the Start button.
Step 4
The use of heat to get your heat gun on the edge of the panel near the bottom right corner of the slide guitar iPad.Gently around the edge of the upper right corner of the front thebottom, which carefulnot of violence and heating the panel, if necessary.
Step 5
Then, to separate the outer edge of the peaks paneland before use / space behind the front tips guitar panel.Insert two spaces for each sideof the IPAD to heat. Be careful when approaching the lower left corner iPad. Be sure to carefully thenext step.
Step 6
After operating the separation of the front of the bottom left corner iPad 2, be careful not to break the digitizercable (marked red in the first frame). It isextremely increase tear.Slightly thin and light, the front panel, near the dock connector that theLCD.Use toseparate foam adhesive mounting to reduce the size of the foam LCD adhesivesecuring a guitar pick in front.
Step 7
Turn the front panel of the iPad, and make sure it does not stick remains twocomponents.Do digitizercable fixing an unreasonable burden.
Step 8
Ask the front panel along with the rest of the iPad 2.Do not try to completely remove thefront panel assembly for now, as shown to the motherboard via ribbon cables attached quietly.
Step 9 – LCD
Remove the four Phillips head screws 2.0 mm securingthe LCD on the back of the box.
Step 10
Lift the LCD longest side closest to the volume buttons and run it on the back of case.Lay LCD on the front panel as shown in Figure TheSecond. 
Step 11
Use the edge of a tool for opening plastic clip to keep your data safe themetal roof monitor cable jack to tilt the board.
Step 12
Disconnect the display data thelogic making board.Do not get up on the screen how to separate the data cable connector.
Step 13
Pull the LCD for the iPad 2
Step 14 – Display of data cable
Remove small strips of black tape on the data cable connector on the LCD thedisplay.
Step 15
Themetal on the edge of an opening tool the plastic to display data cable connector locking clip change.
Step 16
Disconnect the display cable data orbit by LCD.Do not pull up on the screen as you move away another data cable.
Step 17 – LCD
LCD remains.
To reassemble the device, follow these instructions in reverse order. Download here this pdf Manual