forehead - Disassembling HP Photosmart c3180 Feed Roller Assembly Removal Manual Guide

Posted in HP Compaq on 11th February 2013

Disassembling HP Photosmart c3180 Feed Roller Assembly Removal Manual Guide

TOOLS:
Spudger (1)
Torx T10 screwdriver (1)
Disassembly HP Photosmart c3180 power roller Assembly removal
Step 1 – top panel
Before removing the printer, make sure that the printer is disconnected. Turn 90 degrees to the right printer side panel beside the control panel is facing you. Remove the two Torx T10 12 mm screws side panel left.
Step 2
Firmly pull the back of the side panel until it separates from the body of the printer. Turn the panel side upward pulling toward you to remove the Panel.

Step 3
Turn 90 degrees to the right printer. Hold the paper tray and turn down. Insert fingers into the Groove on the door of the printer and pull to rotate the door down.
Step 4
Turn 90 degrees to the right printer. Remove two screws Torx T10 12 mm. Hold both sides of the side panel and pull forward to remove the Panel.
Step 5
Rotate 90 degrees counter-clockwise printer. Lift the scanner lid to expose the scanner glass.
Step 6
Remove two screws Torx T10 12 mm. Do not attempt to lift the lid
Control panel the printer off yet because he is still attached to the body of the printer cable.
Step 7
Rotate 90 degrees counter-clockwise printer. The inside of the printer is a small press tongue white with a spudger inwards until you hear a sound. Remove the front panel by grabbing his forehead and pulling the printer.
Step 8
Turn 90 degrees to the right printer. Remove the top panel of the printer all power button cable.
Step 9
Lift the upper part of the printer away from the body of the printer.
Step 10 – cartridge put to one side of the track on the top panel of the printer.
Remove the two screws Torx T10 12 mm at the front of the printer
Step 11
Does the printer rotates 90 degrees counterclockwise. Remove the cable from the base plate scanner. Take the bottom part of the cable and pull up. Not to move from one side to another or turn it could cause damage to the connection.
Step 12
Turn 90 degrees to the right printer. Using both hands, lift the tray to explore the body of the printer.
Step 13
Remove the support frame power button circuit pinching the left side and pulling forward and to the left at the same time. Click the tab holding the child control with the spudger Board and pull forward to remove it.
CAUTION do not pull hard on the cable that connects the plate power button control and secondary control for main Board
Step 14
Remove two screws Torx T10 12 mm. Lift the support framework outside the body of the printer with both hands.
Step 15
Remove the door and printer paper by putting them in the closed
position and not flat, then turn the left top lift
upward.
Step 16
Remove both ink cartridges holding the front of the cartridge and pulling down. Make sure that the printer carriage is pushed to the right.
Step 17
Remove the 6 mm T10 Torx screws on the left side of the track Assembly. Remove Torx T10 12 mm screws on the left side of the track Assembly.
Step 18
Gently push the carriage to the left of printer ink cartridges.
Step 19
Remove two screws Torx T10 12 mm. Remove the two 6 mm Torx T10
screw.
Step 20
Rotate 90 degrees counter-clockwise printer. Remove truck cable of ink cartridges for the main circuit.
Pull up to the free, the cable to the mainboard. Do not twist or move the cable that you can damage it. You may need to raise with a hand truck to reach the wire with your free hand, as shown.
Step 21
Carefully remove the connector with cables of the motor unit to the
main circuit.
Step 22
Slide the ink cart completely to the right of the printer. Using both hands, gently lift the track from the main part of the printer ink cartridge.
Step 23 – elimination of the set of feed rollers for the transport of the ink cartridge. Remove the three screws Torx T10 12 mm holding the book on the body of the guide of the printer. Pull straight upward to the paper Guide to remove it and set aside.
Step 24
Remove the four screws Torx T10 12 mm roll stand.
Step 25
Remove the plastic gear cover by pulling the printer body and lifting upwards.
Step 26
Remove the filler bracket by turning away from the body of the printer and pulling up. Remove the brush firmly holding the base and the elevation of the right.
Step 27
Remove the holder by lifting it upwards.
Step 28
Remove the connector with the motor of the feed for the logical adapter rollers by pulling on the Strait to remove the 12 mm screws Torx T10 in the scroll pane.
Step 29
Disconnect the sensor from the page of the logical card by pulling upwards on the connector.
Step 30
Resume printer 180 degrees and upload it on the front, then the back of the printer is towards the top and bottom part facing you. Be careful because the Assembly feed roller is now loose, but still joins the main body of the printer. Press the tab on the left side of the back and pull out to remove the back
Panel.
Step 31
Tilt the printer until you can see the bottom of the printer. Remove the bottom panel of 12 screws Torx T10. Grasp the top edge of the lower panel and pull out.
Step 32
Remove the bar cross of black plastic in the bottom of the printer.
Step 33
Decrease the printer so that it sits on the bottom panel and return the printer to 180 degrees.
Step 34
Remove the printhead, cleaning by lifting the front part of the printhead cleaner over the runway and slide it towards the front. It is a very difficult step. It may take a bit of force to lift the cleaner head on the track and is easy to slip and be injured.
Step 35
This step can be done with in the rotation of the printer, but turn off the printer for greater clarity. Take the left side of the feed roller Assembly and pull it towards the front of the printer and high, to release the metal tab on the slot.
Step 36
Lift up feed roller off. Reassemble the appliance, follow these instructions in reverse order. Great Guide DOWNLOAD HERE for this Disassembling HP Photosmart c3180 Feed Roller Assembly Removal Manual Guide