iMac Intel 24″ EMC 2111 Installing Hard Drive Fan Manual Guide
The tools used in this manual
Spudger metal (1)
No. 1 Phillips screwdriver (1)
T6 Torx Screwdriver (1)
T8 Torx screwdriver (1)
Torx T10 (1)
Step 1 – Access Door
Loosen the two Phillips screws to secure the screws to hold your gateway to iMac.Both door.Remove theaccess the gateway in captivity.
Step 2 – Facade
Remove the screws following the lower edge ofyour iMac: Three 6 mm T8 Torx T8 Torx screwsOne 8 mm
Ask your iMac to retire in a flatsurface.To lift the front of the iMac at the same time: Use your thumbs in the arms of RAM andhold push down, use your iMac to the index. ofmaterial take the small bridge in front of his forehead with his index fingers.Once theRAM yourself.Pull the bridge material has been removed the arm, lift the front by its lower edge enough to the bottom of the housing is clear later.
Lift the front of the back cover and turn itaway from the bottom of the iMac, babysitting theCamera cable and the microphone still on the edge itsupper bezelbrackets third photo shows the upper front mounting slots cut in the top of the back cover of the iMac. Not to completely remove the facade, as it is still connected to theCamera / microphone cable.
If necessary, remove the tape from WRAP is the microphone of the microphone cable into the plug top nearthe connector.The iMac.
Disconnect the microphone cable from the camera by pulling the connector cable.Disconnect takeover kann.Sie port of the camera and the camera connector and aredelicate easily folded. Remove withcaution you.
Step 7 – display assembly
Peel the two tiles highlighted theFrame EMI shielding on the LCD.
Remove the two Torx T6 cable attaching the display data to the motherboard.
Pull the black plastic tab on the screen of the data cable from the motherboard to separate.
With your fingers, the two sides of the connection cable of your inverter broad support in the way logicboard.De reversing cable pulling the location of the CPU fan inthe next door.
Before beginning this step, recommendlaying iMac retreat to avoid a fall display down.Remove tableto T8 Torx screws that hold eight rear mounting case.It thedisplay is helpful to use a thin magnetizedscrewdriver to remove the screws.
Remove the display assembly of the iMac.
Step 13 – Right speaker
Peel the piece of tape between EMI thebottom edge of the right speaker to the metal band iMac.Peel frameof at the bottom of the right speaker.
Take the speaker cable to the right of thelogic board and the optical drive fan.
Remove the T10 Torx screw 26 mm theright to iMac speakers.
Disconnect the speaker connector to the left of the edgeof iMac motherboard to separate.
Pull the optical sensor thermal connectortoward on the right side of the box iMac itfrom
If necessary, connect, remove the tape from the optical drive CLOSING.
Pull the cable clamp on the cable connector ZIF optical drive on the right side of the dam should be about 1 mm iMac.The andstop motion. Try not to remove the drive cable retainer.Pull fiber tape from the wall, taking care not to break in the process.
Disconnect the hard drive and cable thermal sensor in the fan disk to the motherboard by pulling theirconnectors to the top of the iMac.
Disconnect the CPU fan in the iMac left side ofThe to separate from the motherboard.
28 Disconnect the power button on the plug logicboard.Pull perpendicular to the motherboard faceof
With the flat of one spudger bluetooth, to increase the antenna from the socket Bluetooth card.
Pull cableperpendicular room temperature sensor on the surface of the motherboard to disconnect, from the base.
Disconnect the cable from the DC-in bypulling your cable on the right side of his depressing mechanism.It iMacwhile lock is useful for a lift and spudger fromalternating pages to use the connection to “migrate” from orbit.
Disconnect the SATA data cable perpendicular tothe front of the board to disconnect from itssocket.To prevent damage to the conquest of the logic board to help, we recommend using a separate metalspudger the SATA data cable and socket.
Peel the foam tape on the top edge sinkframework heat.
Delete the following ten: three T10 Torx screws 6.6 mm fine wire 7 mm coarse thread screwsThree Torx T10 Torx T10 screwsTwo 9.3 mm 5.3 mm thick thread screwsTwo T10 Torx screws coarse thread
Drag the right edge of the plate a little away from the back cover in the back I / S ports bezel.Tilt fromtheir the top of the board away rearcase Remove and lift the main board rearcase, caring for others wires are trapped. When can change the logic board, using tape temporarily thecables ishelpful edge of the road until the plate is sitting in the back of the box isproperly.
Step 34 – hard drive fan
Remove the fan unit positions moldedinto the plastic box. Remove the back of the fan disk …. Download Full Orginal Manual pdf for iMac Intel 24″ EMC 2111 Installing Hard Drive Fan Manual Guide