Toshiba Satellite 1805-S177 Optical Drive Installing Manual Guide

Posted in TOSHIBA on 14th April 2013

Toshiba Satellite 1805-S177 Optical Drive Installing Manual Guide

Toshiba Satellite 1805-S177 Optical Drive Installing Manual Guide

Toshiba Satellite 1805-S177 Optical Drive Installing Manual Guide

Step 1 – battery
Placing the finger on the raised handle, push the battery in the case of the right. You can drag on.

Step 2
Remove the battery housing gently out toward you, until you hear a
clicks. The battery should leave about 2 inches.
Step 3
Lift the battery from the laptop cover.
Step 4-HDD
Look at the bottom of the laptop. With a Phillips screwdriver, unscrew and remove the screw marked F4, on the cover of the hard drive. The hard drive is located in the CD player.
Step 5
Place your finger on the handle raised, push up on the hard drive
coverage. This will remove the hard drive of the laptop cover.
Step 6
With a Phillips screwdriver, unscrew and remove surrounded by white plastic screw.
Step 7
Remove the white plastic to you. This should remove the hard drive
laptop tray unit. This laptop does not have a hard drive, so the tray is empty. On your computer, must be the hard disk in the status bar.
Step 8: keyboard
Stick a wedge on one side of the top panel. Rise slowly from one side to another and will be shown front to the coast.
Step 9
Using a Phillips screwdriver, unscrew and remove the two screws labeled B2.6.
Step 10
With the hand, lift the keyboard towards you, from the edge
closer to the screen. The keyboard is connected to the laptop still a band. Gently place the keyboard on the trackpad, next to the keys.
Step 11
Locate the Ribbon connector white (where the keyboard still joins the rest of the laptop). Drag upwards White Ribbon connector and lift the tape out of it.
Step 12 – TrackPad
With a Phillips screwdriver, unscrew and remove the screw F4 closer to the center of the laptop. This screw is under the battery box, located at the bottom of the laptop directly under the trackpad.
Step 13
With your finger, lift the plastic covering the trackpad by putting your finger on plastic and pulling toward you. The plastic should just pop off.
Step 14
Remove the left Ribbon, Brown, pinching the portion of the tape, connected to the computer
and pulling toward you.
Step 15
Remove the White Ribbon right pinching the part connected to the laptop with the fingers and pulling it toward you.
Step 16
Gently lift the pad to you, with your fingers.
Step 17 – screen
With a Phillips screwdriver, unscrew and remove 5 screws marked F6, located on the metal part on the left side of the keyboard area.
Step 18
With your fingers, pinch and lift the laptop metal part
and set aside.
Step 19
With a Phillips screwdriver, unscrew and remove the screws marked B25 located closer to the screen.
Step 20
With a Phillips screwdriver, unscrew and remove the two screws labeled B5, to the right of where it was the piece of metal. These screws are silver, where all the screws were black.
Step 21
With a Phillips screwdriver, unscrew and remove the two black screws from the back of the laptop. These screws are not labeled.
Step 22
With a Phillips screwdriver, unscrew and remove the screw from F4 of the layer at the bottom of the laptop that only has a plastic
screw.
Step 23
With your fingers, pinch lift plastic hidden away from the laptop and put aside.
Step 24
With your fingers, pinch the black part of the modem, lift and turn up the modem and move it aside. The modem is connected to a red and black cable.
Step 25
Using a Phillips screwdriver, unscrew and remove the two screws from F6 as the modem.
Step 26
With a Phillips screwdriver, unscrew and remove the 5 screws B20, along the corners of the bottom of the laptop.
Step 27
With a Phillips screwdriver, unscrew and remove the three screws of B25 of the bottom of the laptop.
Step 28
With a Phillips screwdriver, unscrew and remove the three screws to F6 from the bottom of the laptop.
Step 29
With a Phillips screwdriver, unscrew and remove the 3 screws of the battery of the laptop F4 area.
Step 30
Open the laptop screen and using your fingers and guides on the side of the laptop, press the plastic cover page from your laptop, moving from one side of the laptop to another.
Step 31
Configuration of the screen next to the base of the laptop, pinch the cable with your fingers and gently pull the monitor connection cable.
Step 32 – optical drive
Remove the part of the computer shows pinching with your fingers plastic and lift the handset.
Step 24
With your fingers, pinch the black part of the modem, lift and turn up the modem and move it aside. The modem is connected to a red and black cable.
Step 25
Using a Phillips screwdriver, unscrew and remove the two screws from F6 as the modem.
Step 26
With a Phillips screwdriver, unscrew and remove the 5 screws B20, along the corners of the bottom of the laptop.
Step 27
With a Phillips screwdriver, unscrew and remove the three screws of B25 of the bottom of the laptop.
Step 28
With a Phillips screwdriver, unscrew and remove the three screws to F6 from the bottom of the laptop.
Step 29
With a Phillips screwdriver, unscrew and remove the 3 screws of the battery of the laptop F4 area.
Step 30
Open the laptop screen and using your fingers and guides on the side of the laptop, press the plastic cover page from your laptop, moving from one side of the laptop to another.
Step 31
Configuration of the screen next to the base of the laptop, pinch the cable with your fingers and gently pull the monitor connection cable.
Step 32 – optical drive
Remove the part of the computer shows pinching with your fingers plastic and lift the handset.
Step 33
Usning the fingers, slide the optical drive of the laptop towards you, then remove it to replace your appliance, follow these instructions in reverse order. Toshiba Satellite 1805-S177 Optical Drive Installing Manual Guide  Donwload HERE dude for images figures

Toshiba Satellite A75-S226 Heat Sink Manual Repair Guide

Posted in TOSHIBA on 13th November 2012

Best way for Toshiba Satellite A75-S226 Heat Sink Manual repair Guide
Gudgel
TOOLS: Phillips 1 Screwdriver (1)Plastic Opening Tools (1)
Step 1 – Battery Be certain that battery-lock is in theunlock position.Slide button to the left
Step 2 Elevate battery out of the computer.
Step three – Onerous Drive Take away two 5.sixty two mm screws from the laborious drive.
Step 4 Use the plastic opening instrument to liftup and remove the arduous drivecover.
Step 5 Slide the hard drive to the appropriate,after which carry it up.Laborious drive not shown inphoto.
Step 6 – CD Drive Take away the 8.6 mm screw.
Step 7 Push the underside left nook of CD Drive until drive protrudes out from the case.Pull the CD Drive out.
Step 8 – Wi-Fi/Reminiscence Cowl Take away the 5.seventy five mm screw from the duvet panel. Step 9 Elevate up the duvet panel using aplastic opening tool.
Step 10 – Wi-Fi
Take away the 5.64 mm screw from the crossing bar.Take away the crossing bar.
Step eleven Use a plastic opening software to take away the black and white wires that connect with the Wi-Ficard.Word that the black wire is linked to the port that labeled main.
Step 12 Use fingers to push the clips away.
Step 13 Remove the Wi-Fi card.
Step 14 – Keyboard Insert the plastic opening toolunderneath the highest panel’s edge.Use the plastic opening instrument to liftup the highest panel all the way alongthe keyboard until it loosens.
Step 15 Remove the top panel.
Step 16 Remove two 3.sixty seven mm screws from the keyboard.
Step 17 Use fingers to lift up the keyboard.Don’t try to take away thekeyboard completelybecause it’s nonetheless attached to themotherboard.
Step 18 Take away the cable connecting thekeyboard with the motherboard.Raise up and take away the keyboard. Step 19 – Display Assembly Remove the 3.76mm screw from the ground wire.
Step 20 Use the plastic opening tool to take away the wire.
Step 21 Gently pull the black and white wires out of the upper case.Don’t pull the wire too much, or you may harm the wire.
Step 22 Remove the 8.6 mm screw.Remove the 8.6 mm screw on leftside of higher case.
Step 23 Remove two 8.6 mm screws on the again edge of the laptop.
Step 24 Elevate up the show meeting toremove it.
Step 25 – Upper Case Use the Phillips screwdriver to remove the two 3.7 mm screws from the batterycompartment.Then remove the fourteen 8.6 mm screws from the bottom of the case.
Step 26 Use the screwdriver to remove six8.6 mm screws from the highest of thecase.
Step 27 Use the plastic opening instrument to remove the two speaker wire connectors and the trackpadconnector from the motherboard.
Step 28 With the plastic opening device, pryaround your entire laptop to separatethe higher case. Step 29 Raise up the higher case to remove.
Step 30 – Motherboard Using the Phillips Screwdriver,remove the two 8.6 mm screwsfrom the entrance edge of themotherboard.
Step 31 Remove the four screws holdingthe ports to the rear panel utilizing the3/sixteen” Wrench.
Step 32 Lift up on the entrance edge of the motherboard while gently prying the case away from theports on the best facet of the computer.Repeat with the left side.There’s a button for the cardboard slot on the left side of the computer that may popout if pressed. This button should be held in place whereas eradicating themotherboard.
Step 33 Raise the motherboard’s front edge upand then slide it forward.
Step 34 – Followers Remove cables connecting the fans with the motherboard.
Step 35 Turn over the motherboard.Take away the four silver screws with a Phillips screwdriver.
Step 36 Flip over the motherboard.Elevate the followers as much as remove themfrom the motherboard.
Step 37 – Warmth Sink With the phillips screwdriver take away the four screws holding the heatsink on themotherboard.
Step 38 Elevate heatsink off the motherboard.There is thermal paste on the underside of the heatsink.When reassembling the heatsink the thermal paste will must be replaced.
To reassemble your gadget, follow these directions in reverse order.
Hey Man HERE for Download full do’nt forget to give thank’s -just kidding-