Samsung - Gadget Owner's manual

Samsung Galaxy Tab Rear Panel Broken Manual Installing

Posted in Samsung on 13th February 2013

Samsung Galaxy Tab Rear Panel Broken Manual Installing
TOOLS:
Metal Spudger set (1)
Tools for the opening of plastic (1)
Y1 Tri-wing screwdriver (1)
iFixit guitar picks up the set of 8 (1)
OVERVIEW
This guide to replace the back of your Samsung Galaxy Tab.

Step 1 – front panel
Use the flat end of a metal spudger to remove the two plastic tabs near the bottom of the connector on the back cover.
Step 2
Remove the two screws from 4.1 mm Tri-Wing near the adjacent edges
the dock dock connector.
Step 3
The following steps will ask to remove several clips (highlighted in red) around the perimeter of the back box. The clips are delicate and fragile; proceed with caution. Install the firewall of the Samsung Galaxy Tab © iFixit – CC BY-NC-SA www.iFixit.com page 3 of 8
Step 4
Warning: The Galaxy Tab, have already had a broken glass panel. However, the procedure described in this guide is identical for the two front panels of broken, intact. Insert an opening of plastic down the edge of the left rear housing of the tool. Use your plastic tool to open gently to create a small gap between the front panel and the back near the left edge of the lower part. Run the tool for the opening of plastic on the left side of the perimeter to create a larger gap between the front and rear. Insert two selections in the small space created by the plastic opening tool.
Step 5
Push the plastic into the dock connector tool and wedge under the set before Panel or the motherboard. Boost plastic tool to open down to create a space near the lower left corner of the front panel of the set. Insert a guitar plectrum in the ditch near the bottom left of the Galaxy Tab recently created.
Step 6
Use caution when approaching the upper-left corner of the Galaxy Tab. Be sure to carefully follow the next step. Separating the front part of the upper-left corner of the Galaxy Tab, make sure not to break the ribbon cable from the microphone (highlighted in red in the first photo). It is extremely thin and easy to tear. Insert an opening tool in plastic in the ditch along the left side of the selection of the guitar.
Don’t forget wedge in the inner frame to take advantage more to release the clips. At the same time lift and run the tool for the opening of plastic along the top left corner of the
Galaxy Tab to release the entire Panel before fixing clips.
Step 7
Slightly lift the left side of the front panel Assembly to separate it from the slot in the rear. Have not fully lifted the
Front Panel Assembly, because it is still sober to the rear by the clips at the top, bottom, right. This can cause serious damage.
Step 8
The flat side of a tool opening between panels front and rear near the connector on the base of the wedge. Use a plastic opening tool to lift the bottom right of the housing at the rear.
Step 9
Lift and remove the rear Panel.
Step 10 – rear panel
Rear panel remains. Reassemble the appliance, follow these instructions in reverse order. Download HERE for This Guide Samsung Galaxy Tab Rear Panel Broken Manual Installing

Samsung Glyde LCD Screen Installing Manual Guide

Posted in Samsung on 10th February 2013

Samsung Glyde LCD Screen Installing Manual Guide

TOOLS:
Desoldering Wick (1)
00 Phillips screwdriver (1)
Tools for the opening of plastic (1)
Kit for welding (1)

Step 1 – battery
With your thumb, press and slide the back cover of the
camera.
Step 2
Remove the battery from the phone.
Step 3 – keyboard
Using a screwdriver, #00, remove the six 4 mm screws hold together the back of the box.
Step 4
Use a plastic opening tool to raise the case. To do this, find a hole on either side of the phone, preferably albums and slide the tip of the tool into the ditch. Now using moderate pressure and slowly move the tool around the outside, up to the case are released. With your fingers, remove the case.
Step 5
The Green film on the camera is your camera to the connector on the motherboard.
Use a plastic opening tool to disconnect the connector of the camera.
Step 6
Gold film connector connects the keyboard to the motherboard. Use a plastic opening tool to disconnect the keyboard connector.
Step 7
Circular connector has the base plate in place. Using a tool opening plastic, circular connector disconnected.
Step 8
There is an LCD screen on the motherboard connector. Gently lift the end of the motherboard toward the center of the phone.
Using a tool opening plastic, disconnect the connector from the LCD screen.
Step 9
Once have disconnected you the four connectors, gently lift the base plate with your fingers. Position the motherboard in a safe place.
Step 10
The antenna is all that is now left out the keyboard. It is the small rectangular object that comes out at the end of “down”. Use a tool to open the plastic pillar antenna. To do this, slide the tip of the tool in one of the edges of the antenna. Use moderate pressure to remove the antenna. An opening with the plastic of the tool, disconnect the connector connects the phone to the antenna.
Step 11
The keyboard is the rectangular object located just at the top. With two fingers, place your phone, use the plastic opening tool to clean the keyboard of the box.
Step 12 – LCD screen
Using a #00 screwdriver, remove the 8 2 mm screws from the display cabinet for sliding mechanism.
Step 13
Now remove the 5 screws 4 mm below the sliding mechanism that are bound to the backplate of the screen. You will have to manipulate the autour de sliding mechanism to get to the screws.
Step 14
Now it is time to desolder components. You can earn some instructions here. Using the bit to solder and a soldering iron, desoldering the contacts of the flex cable.
Step 15
After desoldering it, check that the doors of two flex cables are in “high” position and then deleted.
Step 16
Soft fingers, lift the LCD screen of your accommodation. Warning: Wiring connections all cable LCD they are very sensitive to the touch and react well to throw tear requests.
Reassemble the appliance, follow these instructions in reverse order. to Download this HERE Samsung Glyde LCD Screen Installing Manual Guide