User Manual Free Download

Panasonic - Gadget Owner's manual

Panasonic Lumix DMC-TZ5 Camera Lens Assembly user manual Replacement

Posted in Panasonic on 16th February 2013

Panasonic Lumix DMC-TZ5 Camera Lens Assembly user manual Replacement

TOOLS:
00 Phillips screwdriver (1)
Spudger (1)
OVERVIEW
This guide is to replace the lens in the camera all ready. It will guide you through all the necessary steps to remove the camera. Systems in the area of the lens is not documented here and is to link the complex gear.
Step 1: back cover
Remove the battery and the device’s memory card.
Step 2
Remove the 4 screws on the right side of the camera. There are two upper screws of 3.4 mm. There are two screws 2.2 mm at the bottom.
Step 3
Remove the single screw 3.4 mm on the left side of the camera.
Step 4
Remove the 5 screws from the base of the camera. There are two screws 2.2 mm near the battery compartment. There are three 4 mm screws
Tripod Autour.
Step 5
Slowly slide the back cover to the camera on the back of the housing takes place in place by two ribbon cables. Do not pull the back cover too far from the camera.
Step 6
Disconnect the two ribbon cables using a spudger. Use the tip of the spudger to lift the black clamp, release the ribbon cable.
Step 7
Remove the back of the camera body.
Step 8 – logical front panel
Use the spudger to remove the ribbon cable that connects the lens cover plate by lifting up the black clamp. Carefully remove lid switch function. This unit is turned on and out.
Step 9
Carefully separate the front rear logical map using a logical spudger card.
Step 10
Drag any of the upper part of the camera that is attached to the logic of the camera plate horizontally.
Step 11
Remove the tape from the top of the login page by releasing the black clamp with a spudger. This leaves you with the control panel and Board of higher logical connection free camera separately
Step 12-system of the camera lens
Use a spudger to disconnect the circuit sheet. Lift the black clamp of the release as before.
Step 13
Remove the three screws that hold the lens in place through. The two screws on the left are 4,5 mm with washers. The screw to the right is 4 mm.
Step 14
Gently push the entire lens circuit board and pull
the left side of the first envelope. You will need to move this out gently.
Step 15
Remove all the envelope. Straps on the left and at the bottom of the Assembly are based simply on the housing of the camera. Reassemble the appliance, follow these instructions in reverse order.
Download HERE for this Guide Panasonic Lumix DMC-TZ5 Camera Lens Assembly user manual Replacement

Panasonic Lumix DMC-TZ5 Flash Unit Onw Manual Repair

Posted in Panasonic on 11th January 2013

Panasonic Lumix DMC-TZ5 Flash Unit Onw Manual Repair

TOOLS:
00 Phillips screwdriver (1)
Spudger (1)
OVERVIEW
The flash is attached to the inside of the camera box.

Step 1 – coverage
Remove the battery and memory
Map of the device.
Step 2
Remove the 4 screws from the right
part of the camera.
There are two screws of 3.4 mm to
the upper part.
There are two screws 2.2 mm to
the lower part.

Step 3
Remove the single screw 3.4 mm
on the left side of the camera.
Step 4
Remove the 5 screws from the base of
the camera.
There are two screws 2.2 mm
next to the battery compartment.
There are three 4 mm screws
the Autour de tripod mounting.

Step 5
Slowly slide the back cover
from the device
The back cover is required
instead of two tapes
cables. Do not pull on the back
cover too far from the camera.
Step 6
Disconnect the two ribbon cables using a spudger.
Use the spudger tip to lift the black clamp and release the ribbon cable.

Step 7
Remove the housing towards the back of the
camera.
Step 8 – front plate
Use the spudger disconnect the ribbon cable from the lens to the Platinum case
by lifting the black clamp.
Remove the lid of the function switch. This unit fits in and out.

Step 9
Carefully separate the front logic
Board of Directors of the rear of the base plate
using a spudger.
Step 10
Drag the top of the camera that is connected to the motherboard horizontally
the camera.

Step 11
Remove the upper connection of the Panel ribbon cable by releasing the black clamp with one
spudger.
This leaves you with plate base and top independent free connection Panel
the camera
Step 12 – lens camera Assembly
Use a spudger to separate the Ribbon
Platinum wire. Lift
the black clip upward to unlock as before.

Step 13
Remove the three screws that hold the
a set of lens in its place.
The two screws on the left are
4.5 mm with washers.
The screw is on the right
4 mm.
Step 14
Slightly push lens Assembly
the printed circuit board and pull
the left side of the first envelope.
You won’t need to move this point
gently

Step 15
Remove the envelope.
Straps on the left and the bottom of the set are based simply on the camera housing.
Step 16 – port AV circuit
Use the spudger to unhook the top
flat cable of the turntable.

Step 17
Remove the 2 mm screw in
the lower right corner of the
printed circuit board
Step 18
Gently drag the connections plate. Pull it toward where the
goal used to be. Some earthquake need to be removed.
The plate is installed in the slots on the side of the camera. Not
angle upwards to remove it.

Step 19
Take note of how to integrate the slots for
the circuit for easy
replacement.
Step 20-1e of coverage
After removing the AV platinum album
you stay with the front case
attached to the inside box and
Flash unit.
First, you must remove two 3.5 mm
Blue screw near the hole of the
a lens that includes the inner envelope.

Step 21
Remove the clear of 3.5 mm
screw that puts in place
opening of the inner envelope.
Step 22
Remove the front cover of the
the rest of the unit.

Step 23 – Flash unit
Use a spudger to carefully open the clip just to the left of the device.
Lift the flash out of the housing unit.

To back up your device, follow these instructions in reverse order. Download HERE