HP Mini 1000 WWAN Board Replacement Manual Guide

Posted in HP Compaq on 16th February 2013

HP Mini 1000 WWAN Board Replacement Manual Guide

HP Mini 1000 WWAN Board Replacement Manual Guide

TOOLS:
#0 Screwdriver (1)
Spudger (1)
OVERVIEW
Replace the card in your HP Mini 1000 WWAN.
Step 1 – battery
With detective Conan, place the Mini 1000 top down on a flat surface. Unlock push both the battery to the other.
Step 2
The battery of the Mini 1000 to the nearest edge of the
Open the latches.
Step 3 – keyboard
Remove the two screws according to:
6 Mm Phillips screws
A 4 mm Phillips head screws
Step 4
To facilitate the extraction of the keyboard, it is recommended to make the keyboard out with a hand in the opening (in bold in the third photo) located on the back of the Mini 1000. Everything pushes through the opening with one hand, grasp the left upper edge of the other hand and pull the keyboard towards you. Once established an opening, enter on the keyboard and slowly lift the top perimeter of the top edge.
Step 5
Lift the keyboard from the capital, guard of the cable that is connected to the motherboard.
Step 6
Use your fingernail or the flat end of a spudger to lift valve socket ZIF Cable keyboard. Don’t you forget to look up at the check valve, not the socket itself. Remove the cable from its socket and remove the keyboard.
Step 7-HDD
Use your fingernail or the flat end of a spudger to lift the valve on the card SIM ZIF connector cable Ribbon. Don’t you forget to look up at the check valve, not the socket itself. Remove the SIM card from its backing sheet and pull it up hard disk box.
Step 8
Use your fingernail or the flat end of a spudger to lift valve in hard drive ZIF connector cable. Don’t you forget to look up at the check valve, not the socket itself.
Step 9
Remove the two screws from 4.5 mm to ensure the hard drive in
lowercase letters.
Step 10
Remove the top disc case, taking care of not to damage the cable in the process.
Step 11 – caps
Using the edge of a spudger, lift and remove the four plastic
screw through the bottom of the HP Mini 1000. There are three variants of housings: two Fund tops are short
in height and are trimmed to prevent incorrect insertion of the right upper lid is higher in height and is hacked. The left eyelid is bigger in height and is not notched.
Step 12
Remove the mm four 7 screws that hold uppercase, lowercase.
Step 13
Turn the computer over and open the display. Remove the two screws from 4.5 mm fixing uppercase, lowercase.
Step 14
Wedge the flat end of a spudger between uppercase and lowercase letters in the bottom right of the screen. Lift carefully and the spudger upwards to create a small space between the top of the rock town
and lower case letters. Continue the movement described along the edge right to the capital in order to free the clips secure the capital letters, lowercase.
Step 15
Repeat the same procedure as in the previous step to the declipper along the left side of the capital.
Step 16
Entering the capital and lift slightly, release the remaining clips. The capital is still connected via the TouchPad that is connected to the base plate cable. Do not remove completely the immediate.
Step 17
Put the caps on the top of the upper part of the base plate.
Use your fingernail or the flat end of a spudger to lift the valve in TouchPad ZIF cable. Don’t you forget to look up at the check valve, not the socket itself. Remove your TouchPad ribbon cable. Remove the upper casing of the HP Mini 1000.
-Step 18 WWAN
If applicable, carefully remove the piece of tape covering the WWAN card.
Step 19
Lift the WWAN antenna connectors (2 total) on top of the tray WWAN.
During installation, do not forget to properly connect wire antenna the respective terminals. Antenna red label is connected to terminal ‘hand’ and marked blue antenna is connected to the Terminal “in the.”
Step 20
Phillips WWAN WWAN Council remove only 3 mm bracket screws and the motherboard. During the Assembly, before placing the uppercase WWAN jury, sure that the metal bracket is positioned correctly (as in the second photo). Be careful with the movements of the metal bracket. You can easily become lost in the course of
Disassembly.
Step 21
To remove the screw Phillips that secures the WWAN embark for the
motherboard, the WWAN card should appear on the left side.
Hold the WWAN Council, and directly into your socket on the motherboard. For HP Mini 1000 WWAN Board Replacement Manual Guide
to download this HERE

Disassembling HP Photosmart c3180 Feed Roller Assembly Removal Manual Guide

Posted in HP Compaq on 11th February 2013

Disassembling HP Photosmart c3180 Feed Roller Assembly Removal Manual Guide

Disassembling HP Photosmart c3180 Feed Roller Assembly Removal Manual Guide

TOOLS:
Spudger (1)
Torx T10 screwdriver (1)
Disassembly HP Photosmart c3180 power roller Assembly removal
Step 1 – top panel
Before removing the printer, make sure that the printer is disconnected. Turn 90 degrees to the right printer side panel beside the control panel is facing you. Remove the two Torx T10 12 mm screws side panel left.
Step 2
Firmly pull the back of the side panel until it separates from the body of the printer. Turn the panel side upward pulling toward you to remove the Panel.

Step 3
Turn 90 degrees to the right printer. Hold the paper tray and turn down. Insert fingers into the Groove on the door of the printer and pull to rotate the door down.
Step 4
Turn 90 degrees to the right printer. Remove two screws Torx T10 12 mm. Hold both sides of the side panel and pull forward to remove the Panel.
Step 5
Rotate 90 degrees counter-clockwise printer. Lift the scanner lid to expose the scanner glass.
Step 6
Remove two screws Torx T10 12 mm. Do not attempt to lift the lid
Control panel the printer off yet because he is still attached to the body of the printer cable.
Step 7
Rotate 90 degrees counter-clockwise printer. The inside of the printer is a small press tongue white with a spudger inwards until you hear a sound. Remove the front panel by grabbing his forehead and pulling the printer.
Step 8
Turn 90 degrees to the right printer. Remove the top panel of the printer all power button cable.
Step 9
Lift the upper part of the printer away from the body of the printer.
Step 10 – cartridge put to one side of the track on the top panel of the printer.
Remove the two screws Torx T10 12 mm at the front of the printer
Step 11
Does the printer rotates 90 degrees counterclockwise. Remove the cable from the base plate scanner. Take the bottom part of the cable and pull up. Not to move from one side to another or turn it could cause damage to the connection.
Step 12
Turn 90 degrees to the right printer. Using both hands, lift the tray to explore the body of the printer.
Step 13
Remove the support frame power button circuit pinching the left side and pulling forward and to the left at the same time. Click the tab holding the child control with the spudger Board and pull forward to remove it.
CAUTION do not pull hard on the cable that connects the plate power button control and secondary control for main Board
Step 14
Remove two screws Torx T10 12 mm. Lift the support framework outside the body of the printer with both hands.
Step 15
Remove the door and printer paper by putting them in the closed
position and not flat, then turn the left top lift
upward.
Step 16
Remove both ink cartridges holding the front of the cartridge and pulling down. Make sure that the printer carriage is pushed to the right.
Step 17
Remove the 6 mm T10 Torx screws on the left side of the track Assembly. Remove Torx T10 12 mm screws on the left side of the track Assembly.
Step 18
Gently push the carriage to the left of printer ink cartridges.
Step 19
Remove two screws Torx T10 12 mm. Remove the two 6 mm Torx T10
screw.
Step 20
Rotate 90 degrees counter-clockwise printer. Remove truck cable of ink cartridges for the main circuit.
Pull up to the free, the cable to the mainboard. Do not twist or move the cable that you can damage it. You may need to raise with a hand truck to reach the wire with your free hand, as shown.
Step 21
Carefully remove the connector with cables of the motor unit to the
main circuit.
Step 22
Slide the ink cart completely to the right of the printer. Using both hands, gently lift the track from the main part of the printer ink cartridge.
Step 23 – elimination of the set of feed rollers for the transport of the ink cartridge. Remove the three screws Torx T10 12 mm holding the book on the body of the guide of the printer. Pull straight upward to the paper Guide to remove it and set aside.
Step 24
Remove the four screws Torx T10 12 mm roll stand.
Step 25
Remove the plastic gear cover by pulling the printer body and lifting upwards.
Step 26
Remove the filler bracket by turning away from the body of the printer and pulling up. Remove the brush firmly holding the base and the elevation of the right.
Step 27
Remove the holder by lifting it upwards.
Step 28
Remove the connector with the motor of the feed for the logical adapter rollers by pulling on the Strait to remove the 12 mm screws Torx T10 in the scroll pane.
Step 29
Disconnect the sensor from the page of the logical card by pulling upwards on the connector.
Step 30
Resume printer 180 degrees and upload it on the front, then the back of the printer is towards the top and bottom part facing you. Be careful because the Assembly feed roller is now loose, but still joins the main body of the printer. Press the tab on the left side of the back and pull out to remove the back
Panel.
Step 31
Tilt the printer until you can see the bottom of the printer. Remove the bottom panel of 12 screws Torx T10. Grasp the top edge of the lower panel and pull out.
Step 32
Remove the bar cross of black plastic in the bottom of the printer.
Step 33
Decrease the printer so that it sits on the bottom panel and return the printer to 180 degrees.
Step 34
Remove the printhead, cleaning by lifting the front part of the printhead cleaner over the runway and slide it towards the front. It is a very difficult step. It may take a bit of force to lift the cleaner head on the track and is easy to slip and be injured.
Step 35
This step can be done with in the rotation of the printer, but turn off the printer for greater clarity. Take the left side of the feed roller Assembly and pull it towards the front of the printer and high, to release the metal tab on the slot.
Step 36
Lift up feed roller off. Reassemble the appliance, follow these instructions in reverse order. Great Guide DOWNLOAD HERE for this Disassembling HP Photosmart c3180 Feed Roller Assembly Removal Manual Guide