User Manual Free Download

Desktop PC - Gadget Owner's manual

iMac Intel 27″ EMC 2429 Bluetooth Board Manual Replacement

Posted in Apple, Desktop PC on 29th December 2012

iMac Intel 27″ EMC 2429 Bluetooth Board Manual Replacement
TOOLS:
Heavy suckers (1)
Trombone (1)
Spudger (1)
T9 Screwdriver Torx (1)
T10 Screwdriver Torx (1)
OVERVIEW
Use this guide to replacing the Bluetooth card.

Step 1 – glass panel

Glue a magnet near each of the two upper corners of the glass panel.
To attach the suction cups, we sell, begin by placing the Cup with the mobile
at the same time the handle on the front of the glass (highlighted in the first and the second wall
photos).
Lightly press the suction cups against the glass and lift the movable handle until it is
parallel with the handle (as shown in the third picture).
If their shoots refuse to stick, try to clean the glass and the
Suction Cup with a mild solvent.

Step 2
Lift carefully the glass panel perpendicular to the face of the LCD display just enough to clear the steel
mounting bolts in the bottom of the upper edge of the glass panel.
Lift the glass at the bottom of the iMac and carefully place the Panel aside.
When you reinstall, be sure to clean the inside of the glass panel and
the face of the LCD as any trace of dust or fingerprints stuck inside will be annoying
visible when the computer is turned on.

Step 3: show
Remove the eight screws Torx T10
protect the LCD screen for the outer casing.

Step 4
Carefully determine the iMac stand-lado on a flat surface.
Due to the tight tolerances, you will need to use a thin hook tool to lift the screen in
box. As seen in the first picture, we did one on a bent paper clip.
If you order the double unit kit SSD of iFixit, the kit includes a pair of pliers, tweezers
corner points to work very well for this also.
Use a thin hook tool to lift one side of the upper part of the outer shield of steel
framework.
After lifting the top edge of the screen on the one hand, keep it out of the box
When you use a hook tool to lift the other side.
Lift and hold high enough to access the cable screen.
Do not lift the upper part of the screen’s outer casing too far, as various courts
flat cable always connect the two components

Step 5
Turn off vertical sync cable
in the upper left corner of the
screen. Use the tip of a spudger to
Press the side tabs of the connector.
Step 6
Disconnect the LED backlight
speaker with the hand cable of
by pressing the tab and drag it
at the bottom of the screen

Step 7
Lift the black tab to disconnect the latch cable ZIF data screen
Connector.
Do not pull too hard or you will damage the plug and the socket.
Disconnect the display cable by pulling the connector at the bottom of the screen
the black tab
Step 8
Use the tip of a spudger to
Unplug the power cord from the screen
next to the display cable.

Step 9
Gently pull the screen to
the upper part of your iMac and elevation
except in a case of the iMac.
Step 10 – Council of Bluetooth
The Bluetooth card is located along the left side of the box of the iMac and just underneath of the
LED backlight driver.
Use the flat end of a spudger to gently lift the antenna cord from electrical outlet.
Do not disconnect the antenna by pulling on the cord, since this can damage the
antenna or plug

Step 11
Remove screw Torx T9 Board Bluetooth to the case.
Do not attempt to remove completely the Council yet, as it is still attached by a
cable.
Remove the tape wrapped around the Bluetooth tray, being careful not to put too
tension on the cable connected.
Use the flat end of a spudger to remove the Bluetooth connection data cable and
Remove the Bluetooth card.

To back up your device, follow these instructions in reverse order.

Dwonload HERE for this Guide iMac Intel 27″ EMC 2429 Bluetooth Board Manual Replacement

PowerBook G4 Aluminum 15″ 1.67 GHz Left Speaker Repair

Posted in Desktop PC on 27th December 2012

PowerBook G4 Aluminum 15″ 1.67 GHz Left Speaker Repair

TOOLS:
nut 4 mm (1)
Currency (1)
00 Phillips screwdriver (1)
T6 Screwdriver Torx (1)
PARTS:
G4 aluminum 15 “left speaker 1.67 GHz”
(1)
OVERVIEW
This guide will show you how to remove the left speaker’s PowerBook

Step 1 – battery
Use a coin to turn the battery
90 degrees locking screw
in a clockwise direction.
Lift the battery from the computer.
Step 2 – capital
Remove the following 10 screws:
Two 3 mm Phillips on drums
on each side of the compartment of
the battery contacts.
Four 3 mm Phillips around the
the memory compartment.
Four of the 16 mm Phillips in the
hinge.

Step 3
Open the memory compartment
coverage.
Remove the two 12 mm Phillips
Screw the aluminium support
top of memory
compartment.
Step 4
Turn the computer 90 degrees
in a clockwise direction for power cord
is facing you.
Remove the three 3 mm Phillips
screws along the bottom edge
case.
During the replacement of these
screws, you must install
them in the correct order. Begin by
the closest screw installation of the
display hinge and then go
toward the front of the computer

Step 5
Turn the computer 90 degrees
that clockwise to the faces of the hinge.
Remove Phillips part the bottom 5 mm
screws on each side of the hinge
(two total).
Step 6
Turn the computer 90 degrees
in a clockwise direction for the ports facing you.
Remove the three 3 mm Phillips
screws along the bottom edge
case.
To replace these screws, you
need to install them in the correct
order. Install screws
nearest to the hinge of the screen, then
his way towards the front
the team. Also, make sure that no
Insert the screws in the holes
on each side of the video in the port.

Step 7
Back to the computer and open
the screen.
Remove the two 4.2 mm long, 1.5
Hex screw mm in the upper corners
from the top of the cases (two in total).
A T6 Torx driver, it will work
but will eliminate the repeated use
the screws.
Step 8
Enter in the back corners of the
caps and pull upwards.
Do not pull on the top
case off yet. still have
necessary to disconnect the keyboard
and the touch pad cable.
Lift the back of the box and
work your fingers along the sides,
Release the case as you go. Times
they have launched to the sides, you can
necessary in the case of rock up and down
to release the front part of the capital.

Step 9
Rotate the upper part of the casing at the top and
to the screen, so that the
top cover rests against it.
Step 10
Remove the Orange stripe security
the trackpad for the logic tape
Board of Directors.
Cut the Ribbon of the trackpad
the motherboard upward
in the connector.
Remove the top cover of the
team.

Step 11 – left ambient light sensor
Remove the two 3 mm Phillips
space the fixing screws
light sensor. One is silver and the other
It is, or two blacks.
Disconnect the cable from the
Plate base and remove the left
ambient light sensor of your
team.
Step 12 – left speaker
Remove the hex nut 4 mm security
the left speaker.

Step 13
Disconnect the cable from the left speaker.

To back up your device, follow these instructions in reverse order.

Donwload this Guide over HERE